Téléchargeur: Jasper
Pays: Portugal
Temps de chargement: Oct 11, 2018
Prix: Gratuit
Évaluation: Basé sur 1 utilisateurs

S'il vous plaît, vérifiez que vous n'êtes pas un robot pour charger le reste des pages

tÉlÉcharger bs 6001-1 pdf

Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Wed Jun 28 12:50:35 BST 2006, Uncontrolled Copy, (c) BSI
BRITISH STANDARD
Sampling procedures
for inspection by
attributes —
Part 0: Introduction to the BS 6001
attribute sampling system
ICS 03.120.30
BS 6001-0:
1996
ISO 2859-0:
1995
Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Wed Jun 28 12:50:35 BST 2006, Uncontrolled Copy, (c) BSI
BS 6001-0:1996
Committees responsible for this
British Standard
The preparation of this British Standard was entrusted to Technical
Committee SS/5, Acceptance sampling schemes, upon which the following
bodies were represented:
British Gas plc
British Standards Society
Clay Pipe Development Association Limited
Institute of Metal Finishing
Institute of Quality Assurance
Ministry of Defence
Royal Statistical Society
This British Standard, having
been prepared under the
direction of the Management
Systems Sector Board, was
published under the authority of
the Standards Board and comes
into effect on 15 April 1996
© BSI 10-1998
The following BSI references
relate to the work on this
standard:
Committee reference SS/5
Draft for comment 91/89700 DC
ISBN 0 580 25720 7
Amendments issued since publication
Amd. No.
Date
Comments
BS 6001-0:1996
Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Wed Jun 28 12:50:35 BST 2006, Uncontrolled Copy, (c) BSI
Contents
Committees responsible
National foreword
Page
Inside front cover
iv
Section 1. General
1.1 Scope
1.2 Normative references
1.3 Definitions
Section 2. General introduction to acceptance sampling
2.1 Aim of sampling inspection
2.2 Acceptance sampling
2.3 Choosing between attributes and variables inspection
2.4 Lot inspection
2.5 Sequence or isolated lot inspection
2.6 Acceptable quality level (AQL)
2.7 Process average
2.8 Limiting quality (LQ)
2.9 Normal and tightened inspection
2.10 Reduced inspection
2.11 Switching rules
2.12 Average outgoing quality (AOQ) and its limit (AOQL)
2.13 Item; unit of product
2.14 Nonconformity and nonconforming item
2.15 Critical nonconformities
2.16 Curtailment of inspection
2.17 Disposal of unacceptable lots
2.18 Single sampling
2.19 Operating characteristic (OC) curves
2.20 Double sampling
2.21 Multiple sampling
2.22 Sequential sampling
2.23 Skip-lot sampling
2.24 Comparison of single, double, multiple and sequential sampling
2.25 Drawing of samples
2.26 Sampling plans, schemes and systems
2.27 Distributional characteristics (binomial, Poisson and
hypergeometric)
Section 3. The ISO 2859-1 system
3.1 Description of ISO 2859-1
3.2 Preparing a specification for use in conjunction with ISO 2859-1
3.3 Classification of nonconformities and nonconforming items
3.4 Lots
3.5 Meaning of inspection level
3.6 Setting an inspection level
3.7 Preferred AQLs
3.8 Non-preferred AQLs
3.9 Setting an AQL
3.10 Drawing a sampling plan from the tables in ISO 2859-1
3.11 Normal inspection
3.12 Tightened inspection
© BSI 10-1998
1